JavaScript isn't enabled in your browser, so this file can't be opened. Enable and reload.
MODULE 06 - MOCK TEST 40 MARKS
www.amequestionpaper.in
Contact us for latest Module Question Paper (with answer) & Short Notes
+ 91 755 936 9412
Sign in to Google
to save your progress.
Learn more
* Indicates required question
Email
*
Your email
High carbon steel contain carbon
1 point
a) 0.10 to 0.30 percent
b) 0.30 to 0.50 percent
c) 0.50 to 1.05 percent
Clear selection
Which nut can be rotated by finger
1 point
a) Wing nut
b) Plane check nut
c) Castellated nut
Clear selection
hacksaw blade teeth are
1 point
a) 12 to 1 4 TPI
b) 14 TO 32 TPI
c) 14 TO 42 TPI
Clear selection
Turnbuckle is
1 point
a. Two threaded terminal and barrel
b. Two threaded terminal
c. One threaded terminal and other barrel
Clear selection
Melting point of steel?
1 point
A.2600 F
B.1100 f
C. 1300-1600 f
Clear selection
7 x 9 cable means
1 point
a) nineteen strands for seven wire each
b) seven strands of nineteen wire each
c) both
Clear selection
---- is high in hardness , strength, and corrosion resistant properties
1 point
a) high carbon steel
b) nickel steel
c) chrome –nickel
d) chromium steel
Clear selection
Inconel is
1 point
a) nickel – chromium steel alloy
b) nickel – chromium iron alloy
c) copper and zinc alloy
Clear selection
Aircraft flaring tool must have flaring angle of?
1 point
a) 40-47 degree
b) 35-37 degree
c) 45-47 degree
Clear selection
The most common rotating beam or rotating cantilever test of the the material
1 point
a) Impact test
b) Torsion test
c) Fatigue test
Clear selection
The thickness of cadmium platting deposit is dependent upon the
1 point
a) Voltage & current
b) Time & voltage
c) Time & current density
Clear selection
The type of self locking nut currently in use are the
1 point
a) Boot self locking nut
b) Elastic stop nut
c) Both
Clear selection
The use where the desired tightness can be obtain with the finger and where the assembly is frequently removed
1 point
a) Plane check nut AN 316
b) The light hex nut AN 340 & AN 345
c) The wing nut AN 350
Clear selection
Flare less tube installation
1 point
a) It is important that the find tightness commence at the point where the nut just being to bottom
b) As in (a) and use a wrench and turn the nut 1/6 turn
c) As in (b) and use a wrench on the connector to prevent it from turning the nut
Clear selection
The plastic cannot be reshaped once being cored by heat
1 point
a) Thermoplastic
b) Monolitic
c) Thermosetting
Clear selection
MTCS
1 point
a) A rivet coated with zinc chromate is yellow
b) A rivet anodized surface is Perl gray
c) A rivet metal sprayed is silvery gray color
d) All
Clear selection
In needle bearing
1 point
a) The length of the roller is equal to the dia of the roller
b) The length of roller is many times longer than dia
c) The dia of the roller is 2 times larger than roller
Clear selection
a file test is a method of determining the hardness
1 point
a) a piece of material by trying to cut into if with the corners of a file
b) a piece of material by trying to cut into if without the corners of a file
c) both
Clear selection
Which rivet are used in the interior of the aircraft where clearance is not required
1 point
a) Round head rivet
b) Brazier head rivet
c) Universal head rivet
Clear selection
The strength of which cannot increase by heat treatment
1 point
a) Beryllium copper
b) Aluminum bronze
c) Muntz metal
d) Monel
Clear selection
Type of damage and defect in composite
1 point
a) Crack
b) As in (a) and cosmetic
c) As in (b) and impact
d) As in (c) and holes
Clear selection
MTCS
1 point
a) 10 gauge- blue
b) 15 gauge- red
c) 11 gauge- yellow
Clear selection
In a simpler gear train
1 point
a) At least two or more gear rotate at different shafts
b) As in (a) even number of gear rotate in same direction
c) As in (b) odd number of gear rotate in opposite direction
d) As in (a) even number of gear rotate in opposite direction
Clear selection
When copper wire is replaced by Al wire
1 point
a) Copper wire 2times larger than Al wire
b) Al wire is 2 times larger than copper wire
c) Copper wire 6 times larger than aluminum wire
Clear selection
Shearodising carried out by heating the part in a closed rotating chamber containing
1 point
a) Al oxide at 1400° F
b) Zinc oxide at 1400°F
c) Zinc oxide at 700°F
Clear selection
The hardness test is made with a diamond penetrator in the form of square base pyramid
1 point
a) Brinnel
b) Rockwell
c) Vickers
Clear selection
Scratch abrasion or minor corrosion are smoothed out
1 point
a) Bushing tool
b) Bushing tool & Al wool
c) Al wool
Clear selection
In case of diameter pitch
1 point
a) Higher diameter pitch smaller tooth size
b) Higher dia larger tooth size
c) Lower dia smaller tooth size
Clear selection
MTCS
1 point
a) Group 2 bearing have the largest radius internal clearance
b) Group 4 bearing have the smaller internal clearance & normally used in precision work
c) Normal group bearing are used for most general application where only on owing is interface fit
Clear selection
The spring is used for compression and tension load
1 point
a) Helical spring & tension spring
b) Torsion spring
c) Leaf spring
Clear selection
The fitting are used to joint hydraulics line in areas where connection that is visually maintenance free
1 point
a) Swaged fitting
b) Union fitting
c) Cryot fitting
Clear selection
Which type of corrosion has also called false brinneling
1 point
a) Stress corrosion
b) Integranular corrosion
c) Fretting corrosion
d) Dissimilar metal corrosion
Clear selection
MTCS
1 point
a) Clevis bolt used in tension
b) Eye bolt is used in shear only
c) Jo bolt has the high shear and tensile strength
Clear selection
1100 rivet is used
1 point
a) Soft material
b) Structure part
c) Hard material
Clear selection
In which corroding action take place
1 point
a) 100 &3003
b) 21127 & 2017
c) 3003 & 2017
d) 7075 &2117
Clear selection
The material used for welding
1 point
a) chrome vanadium
b) molybdenum
c) chrome molybdenum
Clear selection
The purpose of lubricant are
1 point
a) Lubricate the area of rubbing contact eg. Between the rolling element
b) As in (a ) cage
c) As in (b) protect from corrosion
d) As in (c) dissipate heat
Clear selection
The disadvantage of titanium is
1 point
a) High melting point
b) Brittle due to long time air
c) both
Clear selection
Which process have wear resistance surface or case over a strong tough case
1 point
a) Annealing
b) normalising
c) Case hardening
Clear selection
The extra flexible cable used in aircraft
1 point
a) Used in primary control
b) As in (a) & not adjusted frequently
c) As in (b) & 7×19
Clear selection
Submit
Clear form
This content is neither created nor endorsed by Google.
Report Abuse
-
Terms of Service
-
Privacy Policy
Forms