W.a.M Level 2 Wood Workshop Induction

JavaScript isn't enabled in your browser, so this file can't be opened. Enable and reload.

All students must pass this quiz (80% correct) as a preliminary induction to access the Machine Shop. In addition a practical induction / training session must be completed in the workshop.

Email *

Student Name *

Student ID # *

1. The WAM machine shop is available for student use after hours. *

1 point

True

False

2. Select from below the mandatory requirements before entering the high risk area of the WAM machine workshop. *

1 point

All students must sign in to the register prior to entry.

Students must ensure they are wearing appropriate PPE including eye and ear protection.

All students must have completed Level 2 Machine Shop induction and training.

All of the above.

3. Select from below the machines students are allowed to use upon completion of Level 2 machine shop induction and training. *

3 points

Band Saws

Drop Saw

Spindle Sander

Wood lathe

Drill Press

Required

4. A student can use the Table Saw if they have completed the necessary training and induction. *

1 point

True

False

5. What does S.W.I stand for? *

1 point

6. When setting up the drill press table and work piece. At what distance should the drill bit be set from the work surface? *

1 point

The depth of the hole you would like to drill

Approximately 10-15mm

The length of the drill bit

Approximately 20 - 25mm

7. Do NOT hold work to be drilled by hand. *

1 point

True

False

8. In what direction should drill bits always be turning to drill a hole through material? *

1 point

Clockwise

Anti - Clockwise

9. If you need to drill a large deep hole, select which 2 techniques below would be useful. *

2 points

Start with a smaller drill bit, then step up a few sizes to the desired hole diameter

Pull down hard on the drill handle.

Drill in stages by going up and down to clear the swarf from the drill bit.

Select full speed on the drill machine.

Required

10. Which of the following should a student adjust or set on the band saw prior to turning on and cutting? *

1 point

Blade guard height to approximately 10-15 mm above the work piece.

The blade tension adjustment dial.

All of the above.

11. What is the minimum distance from the blade that you should keep your fingers away at all times. *

1 point

50 cm

The approximate width of your hand

50 mm

10 - 15 mm

12. Select the mandatory PPE required to be worn when using the band saw in the machine shop. *

2 points

Safety Glasses

Gloves

Ear protection (muffs or plugs)

All of the above

Required

13. Its OK to twist the blade to cut tight curves. *

1 point

True

False

14. A push stick can be used to: (select 2 options) *

2 points

Support or push material when closer than 50mm to the blade.

As a guide to adjust the guard height.

Clear debris (off cuts) from the table.

Slow down the blade after it has been turned off.

Required

15. The band saw is ideal for cutting round material such as rod or dowel. *

1 point

True

False

16. Leather gloves must NOT be worn when using the belt sander. *

1 point

True

False

17. Always ensure that the ........................ system is turned on before operating the sanders. *

1 point

18. Do NOT push materials against the disk or belt sander with excessive force. *

1 point

True

False

19. Select from below some useful applications of the disk sander. *

2 points

Sanding outside (convex) curves on materials.

Sharpening tools such as chisels.

Sanding the end grain of pieces of wood.

Required

20. Looking at the picture of the disc sander and noting the direction of rotation. What side of the blue line should the work piece be placed on the sanding table? *

1 point

Left

Right

21. Select the correct safety procedures when operating sanders from the list below. *

3 points

Ensure that the sander is rotating at full speed before commencing to sand.

Always operate the disc sander with another classmate or student.

Do NOT sand thin or very small pieces of material.

Always check that the table angle is suitable for your task prior to sanding.

Required

22. How many students are allowed in the Wood Machine Shop at any point in time? *

1 point

Submit

Clear form

Never submit passwords through Google Forms.

This form was created inside of Monash University. Report Abuse

Forms