Intro to Wood Shop Quiz

JavaScript isn't enabled in your browser, so this file can't be opened. Enable and reload.

Email *

What is your UNI? (no caps please) *

Which of the following are hazards present in the wood shop? *

3 points

Exposed blades

Splinters

Dust

Loud Noise

Flying debris

Required

Which of the following are required safety precautions before entering the wood shop? *

3 points

Tying back long hair

Removing dangling items like bracelets, necklaces, sweatshirt drawstrings, and loose sleeves

Wearing safety goggles

Wearing closed-toe shoes

Wearing leather gloves

Required

What is a chuck key used for?

1 point

It is the key for turning on the machine.

It is used to turn the chuck jaws to grip the drill bit.

You have to leave it in the drill press to keep the drill bit in place.

Chuck is the wood shop manager, his keys open the wood shop door.

Clear selection

Please label the following parts of the drill press *

8 points

Base

Drill bit

Chuck

Column

Feed wheel/lever

Table

Table Lock

Motor

What is the best way to prevent your work piece from rotating in the drill press?

0 points

Start by using a slow speed, and slowly increase speed as you drill into the material

Start with a smaller size drill bit, and progressively make the hole bigger

Clamp the piece to the table or use the vice

Hold the piece firmly with one hand while operating the feed lever with the other

Clear selection

What materials can you cut with the bandsaw in the wood shop?

2 points

Wood

Wood, but only plywood

Thin sheet metal

Plastic (if you talk to a superuser first to verify)

What is the best hand positioning on your work piece while cutting with the band saw? *

1 point

One hand in front of the piece and one hand behind the piece

You should not use your hands when cutting with the band saw

One hand to the side of the piece and one hand operating the guard height adjustment

Hands on both sides of the piece, never near the path of the blade

Why does the guard height need to be set?

1 point

To improve dust collection

So that less blade is exposed to the user, and to improve the quality of the cut

The bandsaw cannot turn on without the correct guard height

The guard prevents wood chips from falling into the bandsaw

Clear selection

How do you turn off the bandsaw? *

1 point

Press the E-stop and turn off the key. Lightly use the foot brake to slow the blade down

Lower the guard height slowly until the blade comes to a complete stop

Just turn off the key

The on/off switch is located on the rear side of the machine

What is the best way to avoid uneven wear of the sanding belt? *

1 point

Regular maintenance

Flip your piece over regularly so that it doesn't develop sharp spots that damage the belt

Moving your piece side-to-side on the table to utilize the full width of the belt while sanding

Add lubricant to the belt after every time you use the sander

What need to be done to safely put away the miter saw?

2 points

Unplug it

Lock the saw downwards

Clean the blade

Which of the following are hazards of using the sander? *

2 points

Accidentally sanding your fingers by placing them too close to the belt

Accidentally touching the circular sander that turns on at the same time as the belt sander

Loose table adjustment causing your work piece to fall

Dust

Entanglement of loose or dangling items

Required

What type of rectangular dimensions should you cut on our miter saw?

1 point

Wide Longer pieces

Wide Shorter pieces

Thin Longer pieces

Thin Very Small pieces

Clear selection

Why should you be careful when cutting a round object?

1 point

You can lose control of the piece

The quality of the cut is worse

It will wear down the blade

Clear selection

What's the best tool to make this project?

1 point

Tablesaw

Vertical Bandsaw

Miter Saw

Clear selection

What's the best tool to make this project?

1 point

Tablesaw

Vertical Bandsaw

Miter Saw

Clear selection

What's the best tool to make this project?

0 points

Tablesaw

Vertical Bandsaw

Miter Saw

Clear selection

What are valid procedures if you're not sure a procedure is safe?

1 point

Ask a Superuser

Use a different tool

Don't do it

Try it anyway

What cleanup steps should you always follow after using the wood shop? *

2 points

Put all tools and equipment away

Brush or vacuum your work area

Turn off the dust collection system if no one else is using it

Lubricate and tune the machines if necessary after use

Return all protective equipment, such as goggles and hearing protection

Required

Submit

Clear form

Never submit passwords through Google Forms.

This form was created inside of LionMail.

Does this form look suspicious? Report

Forms