您的浏览器中未启用 JavaScript，因此无法打开此文件。请启用 JavaScript，然后重新加载。
Lathe 101 Quiz
This quiz the Lathe 101 video
登录 Google
即可保存进度。
了解详情
* 表示必填
电子邮件地址
*
您的电子邮件
Name
*
您的回答
How many minutes do you get for one valid scan on Tinkeraccess.
*
1 分
150
100
200
50
必填
Why would the big red flashing light come on?
*
1 分
One of the machines is low on oil.
There is a fire in the building.
There is 5 mins left before Tinkeraccess times out.
Somebody hit the E-Stop on Tinkeraccess
必填
What is "backlash"?
*
1 分
It is the movement allowed on the tail stock.
It is the play we have in the screws on the lathe.
It is the movement in the spindle when you stop the machine.
It is the tolerance in the collet closer.
必填
What is a good drilling speed on the lathe?
*
1 分
300 RPM.
125 RPM.
60 RPM
400 RPM
必填
Name two types of taps?
*
1 分
Taper tap and plug tap?
Starter tap and bottom tap.
Screw tap and bolt tap.
Water tap and oil tap.
必填
When can you open the lathe door at the back to get access to the circuit breakers?
*
1 分
While the machine is not running.
While the power switch is in the "OFF" position.
While the power is off - i.e. Tinkeraccess logged out.
While the E-stop on the front panel is activated.
The head stock is ... ?
*
1 分
The big nut on top of the tool holder.
The collective name for the cross slide and compound slide.
The part that contains the spindle and gear box.
The lever on the left side that closes the collets.
How do you remove the drill chuck from the tail stock?
*
1 分
Simply pull it out.
Crank the cylinder back in until it pops out.
Whack it with a dead blow hammer until it pops out.
Use the spanner wrench.
How many lubrication holes on the compound slide?
*
1 分
9
10
3
2
必填
What happens when you throw the lathe in reverse while it is running at full speed in the forward direction?
*
1 分
You will strip the gears in the gearbox.
It will immediately attempt to reverse and possibly break the belts between the motor and gearbox
It will ignore you and keep running in the forward direction.
It will come to a stop and then start up in reverse.
Name the two typical drill bit angles?
*
0 分
90 and 180
118 and 135
70 and 90
100 and 120
Name the four types of drill sizes?
*
0 分
Fractional, SAE, Metric and NPT.
Fractional Inch, Number, Letter and Metric.
Inch, mm, Angstrom and Parsec.
Thousands of an inch, Fractional and decimal.
What do I do when the gearbox levers refuses to move into position?
*
0 分
Tap it with the dead blow hammer.
Put force on it.
Move the spindle and gently try again.
Start / stop the spindle and try again.
What is a center drill used for?
*
0 分
To drill out broken drills.
To find the center of an existing hole.
To chamfer an existing hole.
To start a hole.
A carbide cutter is usually run at a _____? speed compared to HSS.
*
Higher
Similar
Slower
Does not matter.
Sandpaper must not be used on the lathe because
*
0 分
It generates too much heat.
It is ineffective.
The residue is abrasive and will damage the ways.
It can catch fire.
提交
第 1 页（共 1 页）
清除表单内容
切勿通过 Google 表单提交密码。
此表单是在 TinkerMill 内部创建的。
举报滥用行为
表单
